Maintenance · 4 min
How to Winterise Your Pool and Protect Your Salt Chlorinator in Winter
Enjoying a pool with crystal-clear water thanks to a bspool electrolysis system is one of the great comforts of summer. Our units, from the efficient BSV Evo series to the robust BSV Pro models, are designed for maximum automation and minimal maintenance.
However, when the swimming season ends and temperatures drop, it is crucial to winterise properly. It is not just about covering the pool; it is about protecting the most valuable component of your system: the electrolysis cell.
Incorrect winterising is the main cause of problems in spring. As water treatment experts, at bspool we want to guide you to make sure your unit is perfectly protected during the winter and ready to start up without problems next season.
The key step: understanding your Bspool chlorinator and the cold
The heart of your system, your salt chlorinator, works by turning salt into chlorine. This process depends on the conductivity of the water, which drops significantly in the cold.
BSPOOL disinfection systems can be equipped with temperature probes that automatically stop chlorine production when the water drops below 15°C. This is a vital safety feature that protects the cell from unnecessary wear.
But be careful: the chlorinator switching off on its own does not mean the pool is winterised. The equipment (cell, pump, filter) is still full of water, and the pipes are vulnerable to freezing in extreme climates, so active winterising becomes essential.
Winterising guide in 6 steps
Follow this protocol for a professional end to the season.
1. Thorough cleaning
You can’t winterise a dirty pool. Any leaves, algae or organic matter left will decompose, staining the lining and becoming food for algae in spring.
- Brush the walls and floor thoroughly.
- Vacuum the whole pool meticulously.
- Clean the waterline.
- Do a thorough backwash of the sand filter or clean the cartridges.
2. Perfect chemical balance
The water should go to “sleep” chemically stable. This prevents corrosion and scaling and makes start-up easier in spring.
- Salt level: Measure the salinity. It should be in the optimal range for your bspool unit (usually 4-5 g/l). It is easier to adjust the salt now than with cold water.
- Alkalinity (TA): Adjust it to between 80 and 120 ppm.
- pH: Stabilise it between 7.2 and 7.8. This is the most important step for the other products to work.
3. Shock treatment (superchlorination)
Even if your bspool chlorinator has a “Boost” function, for winterising we recommend manual superchlorination with granular dichlor or liquid hypochlorite. This creates a powerful disinfectant reserve that will eliminate any dormant bacteria or algae. Leave the filtration running for 12-24 hours.
4. The critical step: the Bspool chlorination cell
This is the most important step to protect your investment.
- Switching off and disconnecting: Disconnect the main power supply to your bspool chlorinator’s panel.
- Removing the cell: Close the cell’s isolation (bypass) valves. Carefully unscrew and remove the electrolysis cell from the pipe.
- Inspection and cleaning: bspool pool salt chlorinators (such as the BSV series) have self-cleaning cells with polarity reversal, so they should be clean. Even so, inspect it visually. If you see white limescale deposits, soak it in a specific cell cleaner until the plates are clean. Important: Never scrape the plates with metal objects or hard brushes. You would damage the surface coating.
- Storage: Once clean and dry, store the cell in a dry, protected place and, above all, where it cannot freeze (garage, indoor plant room, etc.).
5. Protecting the filtration system
Water that freezes inside the filter or pump expands and bursts them.
- Lower the water level: In areas with frost, lower the water level below the skimmers and return inlets.
- Drain completely: Empty the filter completely (using its drain plug), the pump (removing its drain plugs) and any exposed pipework.
- Selector valve: Leave the filter valve lever in the “Winter” or “Closed” position (see the filter manual).
6. Winterising product and cover
- Add a winterising product: Use a long-lasting winterising product. It is a powerful algaecide that will keep the water clear. Make sure it is compatible with salt electrolysis (usually copper sulphate-free).
- Cover the pool: Fit an opaque winter cover. This blocks sunlight (preventing photosynthesis) and keeps dirt out, protecting the lining.
Your Bspool unit, protected
A few hours of work now will save you money and headaches in spring. Storing the cell correctly is the guarantee that, when the warm weather returns, your bspool system will start up easily.
This process ensures maximum durability of our pool salt chlorinators and gives you the peace of mind of knowing your pool is perfectly protected by the experts.
For more information about your specific model, visit bspool.eu and check our product manuals.
-
5 min read
-
3 min read
Maintenance
How to maintain your pool after the summer?
-
3 min read
Maintenance
Summer is coming! How to prepare your pool
-
3 min read
Maintenance
Is your pool protected from the rain?
-
2 min read
Maintenance
Pool maintenance after the summer
-
2 min read
Maintenance
Get your pool ready for summer
Got a question that none of our articles answers?
Our technical team replies in writing within 24 business hours, and the official service network covers all of Spain.