OFFICIAL TECHNICAL SUPPORT

Specialist support and documentation in a single click

MANUALS AND INSTALLATION Manuals and videos

Every unit, with all its documentation. Every unit, with its manual and video.

Step-by-step guides, assembly manuals, exploded views and video content.

INSTALLATION AND START-UP

From installation to start-up, step by step.

Official assembly protocols aligned with the 2026/2027 catalogue to ensure maximum durability and performance of your equipment.

PHASE 01

Installation protocol

4 steps

  1. Equipment switched off and disconnected from power

    Disconnect the main power supply before handling the control panel.

  2. Installing the control unit

    Mount on a ventilated wall, protected from direct sunlight and with an earth connection.

  3. Installing the cell

    Vertical position on the return line (in bypass), always after the filtration system.

  4. Electrical connection of the cell

    Connect the cell cables to the control panel according to your model's wiring diagram.

    Depending on model

THE UNIT IS NOW INSTALLED

FREQUENTLY ASKED QUESTIONS

Clear answers for the daily care of your water.

We answer the most common questions received by our technical team. If you can't find the answer, use the search bar at the top to look up your model's manual.

Why is the water greenish or brown, and how do I fix it?

Greenish water: indicates algae caused by low disinfection levels, a pH imbalance or insufficient filtration.

Steps to restore water clarity:

  • Adjust the pH: check it and keep it within the optimal range (between 7.2 and 7.4).
  • Shock treatment: activate the superchlorination function on your salt unit or carry out a shock chlorination, keeping filtration running for 24-48 h.
  • Cleaning and clarifying: brush the walls and floor, apply flocculant and backwash the filter at the end of the process.
Why is the water brownish, and how do I fix it?

Brownish or brown water: usually caused by oxidation of metals (iron or copper) present in the fill water.

Steps to restore water clarity:

  • Adjust the pH: check it and keep it within the optimal range (between 7.2 and 7.4).
  • Avoid initial shock chlorination: if the source is well-water iron, chlorine will oxidise it further and make it darker.
  • If it is caused by metals (well water): add a metal sequestrant directly to the water.
Why does the water smell strongly of chlorine or sting the eyes, and how do I fix it?

Contrary to popular belief, a strong chemical smell and eye irritation are not caused by too much chlorine, but by the presence of chloramines (combined chlorine). These form when the disinfectant combines with organic matter and the water is not properly renewed or disinfected.

Steps to eliminate chloramines:

  • Adjust the pH: keep it strictly between 7.2 and 7.4. An unbalanced pH drastically reduces treatment effectiveness.
  • Superchlorination / chloramine destruction: activate superchlorination mode on your BS Pool salt unit (or apply a shock treatment) to break down the chloramines and restore water purity.
  • Renewal and filtration: keep filtration running continuously for 24 h and ensure good pool recirculation.
Is it normal for a disinfected pool to lose chlorine after filtering?

Yes. Sunlight, high water temperature and bathers constantly consume free chlorine, even if the unit has been running.

BS Pool recommendations:

  • Check the pH range.
  • Align filtration hours and salt output with the hours of strongest sunlight.
  • Automate readings with ORP/redox sensors to respond to demand in real time.
How often should I chlorinate the pool if it is hardly used?

Disinfection should be daily and continuous, but at a lower intensity. Salt systems let you set output to the minimum needed to prevent algae or bacteria growth.

Key guidelines:

  • Set the chlorinator output to 10%-20% and reduce filtration hours.
  • Keep the pH between 7.2 and 7.4.
  • Monitor parameters remotely with the BSLINK platform.
What causes limescale and how do I remove it?

It appears due to alkaline (high) pH or very hard water. It causes white stains in the pool and clogs the salt chlorinator's plates.

Quick fix:

  • Check and lower the pH to a range of 7.2 to 7.4.
  • Make sure the unit's polarity reversal function is active for cell self-cleaning.
  • Use a maintenance anti-scale product if your mains water is very hard.
What causes algae in the water?

Algae appear due to a lack of active chlorine in the pool, encouraged by high pH, insufficient filtration or high water temperature.

Quick fix:

  • Adjust the pH to 7.2 – 7.4.
  • Run a superchlorination with the salt unit (Boost mode) and filter non-stop for 24 to 48 h.
  • Brush the pool, apply flocculant and clean the filter afterwards.
What happens when the pool's alkalinity is very high?

It locks the pH at high values, clouds the water and increases limescale build-up in the equipment, as well as reducing chlorine efficiency.

Steps to fix it:

  • Apply pH reducer in measured doses to lower alkalinity to the 80 – 120 ppm range.
  • Filter continuously to evenly distribute the treatment.
  • Automate readings with the salt chlorinator kits to protect the salt cell.
How does low alkalinity affect the pool?

Low alkalinity causes a series of problems both in the water chemistry and in the pool's structure and equipment: unstable pH, corrosive water, irritation for bathers and green or cloudy water.

Steps to fix it:

  • Use alkalinity increaser in the proportion recommended by the manufacturer.
  • Keep filtration running for 24 h.
  • Measure and adjust the pH to 7.2 – 7.4.

TROUBLESHOOTING

Your unit is warning you: learn how to read its messages.

Guide to display alerts with the step-by-step checks you can carry out and the official recommendation for requesting technical support.

Tap the alert you see on the display.

  • Low salt

    The salt concentration is below the minimum working level and output drops.

  • Too much salt

    There is too much salt in the water. It does not affect operation or the cell's lifespan.

  • Cleaning

    The unit has switched to cleaning mode to optimise the cell.

  • Temperature

    The unit is overheating internally. When the temperature drops, it will automatically return to normal operation. This alarm stops the unit when the ambient temperature is above 40 °C.

  • Temperature flashing

    The water temperature is below 15 °C.

  • No flow

    This may be because there is no water circulating through the cell housing or there is excess gas in the electrolytic cell, for example because the pump has stopped. Check the installation.

  • Open circuit

    Check the connection of the cell cables to the unit.

  • Short circuit

    Check that there are no foreign objects in the cell housing.

  • CL error

    Indicates a malfunction in the redox or free chlorine probe. When the reading stays at one value for a certain period (usually 0 or a value that does not change), production stops and this error appears.

  • pH error

    Indicates that the pump has been running non-stop for 2 h and stops it, although not the chlorinator.

Request a repair for your unit

Download the official repair request (RMA), find your assigned centre and send the unit, properly protected, for inspection by the SAT.

  1. Download and complete the RMA form
  2. Find your Official Technical Service (SAT)
  3. Attach the document and include the unit in the package

OFFICIAL SERVICE NETWORK

Find your nearest official technical support centre

Direct factory support throughout Spain. Enter your location to find the Official Technical Service (SAT) or authorised distributor assigned to your area.

Tell us where you are and we will tell you who will assist you.

21 centres in the network